Railworks America

I have released the repaint of the RSC ES44AC CSX locomotive in Florida East Coast Railway livery.
Enjoy!

Dave

Great work!

Good work!

Thank you

All we need now is a FEC route to run these beasts on.

Harry

I downloaded these but I can't seem to get them to work. I followed the instruction on the .txt file that came with it and put the FEC folder in with the CSX ES44AC file, but when I try launching a Quick Drive scenario it just says it fails to load the scenario.

floridarails63 wrote:I downloaded these but I can't seem to get them to work. I followed the instruction on the .txt file that came with it and put the FEC folder in with the CSX ES44AC file, but when I try launching a Quick Drive scenario it just says it fails to load the scenario.

Welcome to RWA floridarails63. The instructions to install this repaint are as follows:

This package will install a repaint of the RSC ES44AC CSX locomotive in Florida East Coast Railway livery.
1. Unzip the ES44C4 zipped file and run the setup utility.
2. Navigate to the following directory in your Train Simulator instalation:
RailWorks\Assets\RSC\ES44AC_Pack01_CSX_YN3\RailVehicles\Diesel\ES44AC\ES44AC_CSX_YN3\Engine
3. Copy the ES44_CSX_YN3.GeoPcDx file.
4. Now navigate to the directory:
RailWorks\Assets\RSC\ES44AC_Pack01_CSX_YN3\RailVehicles\Diesel\ES44AC\FEC\Engine
5. Paste the copied file from step three in this location.
Enjoy the repainted locomotive!
Regards,
Dave

If you follow each step of the instructions with a clean install of TS and the RSC original asset you should have no problem.
There is nothing in the instructions directing you to: "put the FEC folder in with the CSX ES44AC file". I don't know what that means.
If you have moved, edited, or otherwise changed the TS or asset files from their defaults, I'd have no idea what is happening.
I would suggest starting with a clean install of TS and the RSC CSX ES44AC asset. Make sure that is all working, then follow these instructions, step by step.
Good luck and let us know how it goes.

Welcome to RWA floridarails63. The instructions to install this repaint are as follows:

This package will install a repaint of the RSC ES44AC CSX locomotive in Florida East Coast Railway livery.
1. Unzip the ES44C4 zipped file and run the setup utility.
2. Navigate to the following directory in your Train Simulator instalation:
RailWorks\Assets\RSC\ES44AC_Pack01_CSX_YN3\RailVehicles\Diesel\ES44AC\ES44AC_CSX_YN3\Engine
3. Copy the ES44_CSX_YN3.GeoPcDx file.
4. Now navigate to the directory:
RailWorks\Assets\RSC\ES44AC_Pack01_CSX_YN3\RailVehicles\Diesel\ES44AC\FEC\Engine
5. Paste the copied file from step three in this location.
Enjoy the repainted locomotive!
Regards,
Dave

If you follow each step of the instructions with a clean install of TS and the RSC original asset you should have no problem.
There is nothing in the instructions directing you to: "put the FEC folder in with the CSX ES44AC file". I don't know what that means.
If you have moved, edited, or otherwise changed the TS or asset files from their defaults, I'd have no idea what is happening.
I would suggest starting with a clean install of TS and the RSC CSX ES44AC asset. Make sure that is all working, then follow these instructions, step by step.
Good luck and let us know how it goes.

Hi, sorry for the confusing wording. I ran the setup but the assets weren't in the ES44AC folder, so I took the FEC folder from the Upload folder and manually put it in. I guess it didn't install properly because I didn't have a clean install of the game (had other mods). I did a re-install of the game to get a clean slate and ran the setup and navigated to RailWorks\Assets\RSC\ES44AC_Pack01_CSX_YN3\RailVehicles\Diesel\ES44AC\. I then realized the FEC folder wasn't in there. When you launch the game and make a custom consist the locomotive doesn't appear either. Not sure if the setup installed it properly or not.