Railworks America

I'm testing out some new whistles and bells with my G-TraXs Berkshire (I test all of my steam loco sounds on the berkshire) and it keeps making TS2013 crash. Does anyone know what the problem is?

Re-working Audio files is a little more involved that just dropping sound files into the Audio folders and over-writing the old files. The BluePrint files must be carefully scrutinized to make sure that the names for the sound objects are observed and the folder addresses where they can be founded are referenced correctly. Also, RW uses a .DAV format for audio files, where as most re-worked bell and whistle sound files may be in .WAV or .WMA format. The BluePrint files must be edited to recognize the difference as I have painfully learned.

OlPaint

OlPaint wrote:Re-working Audio files is a little more involved that just dropping sound files into the Audio folders and over-writing the old files. The BluePrint files must be carefully scrutinized to make sure that the names for the sound objects are observed and the folder addresses where they can be founded are referenced correctly. Also, RW uses a .DAV format for audio files, where as most re-worked bell and whistle sound files may be in .WAV or .WMA format. The BluePrint files must be edited to recognize the difference as I have painfully learned.

OlPaint

I don't think you understand. I've changed the sounds many times before. I even made a bell sound replacement for it, check the file library. What I'm saying is that I go to start a scenario with the Berk and a changed sound, the scenario loads, and immediately the game crashes. I get that "Something bad happened in the program" message. But when I use the default sounds, the scenario loads and the game doesn't crash.

Think this through for a minute my young friend. You have to be doing something different. Have you put YOUR file that you know works in there and is it OK? If so something must be wrong with your new one.

buzz456 wrote:Think this through for a minute my young friend. You have to be doing something different. Have you put YOUR file that you know works in there and is it OK? If so something must be wrong with your new one.

Well, my bell replacement still works. So, I guess my audio files are broken. Is there any way to fix them?

Railfan587 wrote:

buzz456 wrote:Think this through for a minute my young friend. You have to be doing something different. Have you put YOUR file that you know works in there and is it OK? If so something must be wrong with your new one.

Well, my bell replacement still works. So, I guess my audio files are broken. Is there any way to fix them?

Problem solved. I use the "&" for SP&S 700 Whistle. I changed it the SPS 700 Whistle, and now it is working.

Another Shazaam!

Good! Now upload it to the file library Asap!

CSX2057 wrote:Good! Now upload it to the file library Asap!

They're submit to the file library.

Thx railfan! Gonna download tommorrow

Bob is off rail fanning this weekend with his fellow NERW creators so you probably won't see any updates until next week.

buzz456 wrote:Bob is off rail fanning this weekend with his fellow NERW creators so you probably won't see any updates until next week.

Here CSX.

Railfan587 wrote:

buzz456 wrote:Bob is off rail fanning this weekend with his fellow NERW creators so you probably won't see any updates until next week.

Here CSX.

SPS_E1_Northern_Whistle_and_Bell_Replacemant.zip

Very nice whistle! I'll get right on there!

Take as time as you need for the other 2.

The SP GS-4 is done too, but it is bigger than 2 mg.

SO, I was quite happy to see some enhancement sounds for the SP&S 700, so I downloaded them and after reading the readme repeatedly, I put the files where they go and the only sound that works is the Whistle (which sounds AMAZING). My 700 is the quietest steam loco in the world cause it's dead silent...minus the whistle.

I'm not sure if I did something wrong...

Any help would be wonderful! Thank you