U30c won't move
Posted: Thu Nov 22, 2018 6:14 pmI start up the Chessie u30c and it won't move I follow everything and I put the power switch in move position and it won't let me move the throttle 
Railworks America
https://www.railworksamerica.com/forum/
U30c won't move
https://www.railworksamerica.com/forum/viewtopic.php?f=29&t=20662
Page 1 of 1
Posted: Thu Nov 22, 2018 6:14 pmRe: U30c won't move
Posted: Thu Nov 22, 2018 6:47 pmReading the manual and watching a couple tutorials on youtube goes a long way..
Re: U30c won't move
Posted: Thu Nov 22, 2018 9:23 pmBNSFdude wrote:Reading the manual and watching a couple tutorials on youtube goes a long way..
But I read the manual many times and I watched a bunch of videos
Re: U30c won't move
Posted: Thu Nov 22, 2018 10:19 pmSometimes the dynamic brake handle isn't all the way off on that in the beginning if you can't move the throttle handle. If you can move the throttle handle then make sure the hand brake is off.
Re: U30c won't move
Posted: Fri Nov 23, 2018 10:11 amEngineerJohn wrote:Sometimes the dynamic brake handle isn't all the way off on that in the beginning if you can't move the throttle handle. If you can move the throttle handle then make sure the hand brake is off.
I've tried that and the throttle won't move
Re: U30c won't move
Posted: Mon May 04, 2020 8:46 pmThe steam version of the VRC U30C has had an issue in which the throttle won't move if you play the game in 64bit mode. This has made an otherwise very good locomotive, unusable unless you're ok with only running in 32bit mode.
Well, there is a fix for this issue. Just follow these steps:
1. On the Railworks America homepage, click on "File Library" and then "Models" and then do a search in the upper right corner for ( RW&A GP40 and GP30 slug unit ). Or try following this link; ( http://www.railworksamerica.com/index.p ... ide-addons ).
2. Download and install the ( RW&A GP40 and GP30 slug unit ). It will install into VRC/RWA-GP40-01.
3. Now, go into the following folder, "VRC/RWA-GP40-01/LuaLibrary", and copy the file "CommonLib-1.1.out".
4. Paste this file into your "VRC/U30C-Series_01/LuaLibrary" folder and when asked to overwrite, say yes. ( Please backup the original file first, just in case!!! )
5. Make sure to delete the file, "Blueprints.pak" in both your "VRC/U30C-Series_01" folder and the "VRC/RWA-GP40-01" folder, if there is one there. ( Don't worry, the game will make a new one once you start the game. )
6. That's it! You should now be able to run the U30C in 64 bit mode with no problems now.
I hope this helps,
Wopflyer
Well, there is a fix for this issue. Just follow these steps:
1. On the Railworks America homepage, click on "File Library" and then "Models" and then do a search in the upper right corner for ( RW&A GP40 and GP30 slug unit ). Or try following this link; ( http://www.railworksamerica.com/index.p ... ide-addons ).
2. Download and install the ( RW&A GP40 and GP30 slug unit ). It will install into VRC/RWA-GP40-01.
3. Now, go into the following folder, "VRC/RWA-GP40-01/LuaLibrary", and copy the file "CommonLib-1.1.out".
4. Paste this file into your "VRC/U30C-Series_01/LuaLibrary" folder and when asked to overwrite, say yes. ( Please backup the original file first, just in case!!! )
5. Make sure to delete the file, "Blueprints.pak" in both your "VRC/U30C-Series_01" folder and the "VRC/RWA-GP40-01" folder, if there is one there. ( Don't worry, the game will make a new one once you start the game. )
6. That's it! You should now be able to run the U30C in 64 bit mode with no problems now.
I hope this helps,
Wopflyer